Fix Automatic/Startup Repair Couldn't Repair Your PC in Windows 10

In some cases, Windows 10 Automatic Repair couldn't repair your PC error can be caused by your hard drive, and the only solution is to reconnect it. Just turn off your PC, unplug it, open it, and disconnect your hard drive. Now you just need to reconnect your hard drive, connect the power cable, and start it again.

1. How do I fix startup repair couldn't repair my computer?
2. How do I bypass automatic repair on Windows 10?
3. Does Windows 10 have a repair tool?
4. Can't even boot into Safe Mode?
5. Why is my PC doing automatic repair?
6. How do I get out of the preparing automatic repair loop?
7. How do I boot up in safe mode?
8. How do I fix startup problems?
9. Is Startup Repair Safe?
10. What do I do when startup repair takes so long?

How do I fix startup repair couldn't repair my computer?

Automatic Startup Repair couldn't repair your PC

1. Rebuild BCD & Repair MBR.
2. Run chkdsk.
3. Run SFC and Use DISM Tool in Safe Mode.
4. Disable Early launch anti-malware protection.
5. Disable Automatic Startup Repair.
6. Restore registry from RegBack directory.
7. Reset This PC.

How do I bypass automatic repair on Windows 10?

Method 5: Disable Automatic Startup Repair

In Command Prompt, type bcdedit /set default recoveryenabled No and press Enter. Restart your PC, the Automatic Startup Repair should be disabled and you might be able to access Windows 10 again.

Does Windows 10 have a repair tool?

Answer: Yes, Windows 10 does have a built-in repair tool that helps you troubleshoot typical PC issues.

Can't even boot into Safe Mode?

Here are some things that we can try when you're unable to boot into safe mode:

1. Remove any recently added hardware.
2. Restart your device and long press the Power Button to force shutdown the device when logo comes out, then you can enter Recovery Environment.

Why is my PC doing automatic repair?

A bad system update, a new graphics card, corrupted system files, even a fresh USB mouse—any of these can cause a dreaded Windows 10 automatic repair loop to occur when you're trying to boot up a Windows PC. ... If Windows can't repair itself, it reboots and repeats the cycle.

How do I get out of the preparing automatic repair loop?

If your Windows cannot boot because of the "Preparing Automatic Repair" or "Diagnosing your PC" error, you can do a hard reboot.

1. Remove the battery and AC adapter.
2. Press and hold the power button for 20 seconds and see if it will boot up normally.

How do I boot up in safe mode?

1. Restart your PC. When you get to the sign-in screen, hold the Shift key down while you click Power. ...
2. After your PC restarts to the Choose an option screen, go to Troubleshoot > Advanced options > Startup Settings > Restart.
3. After your PC restarts, you'll see a list of options. Press 4 or F4 to start your PC in Safe Mode.

How do I fix startup problems?

First, power the computer completely down. Next, turn it on and keep pressing the F8 key as it boots. You'll see the Advanced Boot Options screen, which is where you would launch Safe Mode from. Select “Repair Your Computer” and run startup repair.

Is Startup Repair Safe?

ESG team of PC security researchers strongly recommends removing Windows Startup Repair from your computer as soon as Windows Startup Repair is detected. An anti-malware tool that is fully up to date should be able to detect and remove any trace of a Windows Startup Repair infection.

What do I do when startup repair takes so long?

1. Restart your computer.
2. Start pressing F8 repeatedly until the Startup Options screen is displayed.
3. Select Safe Mode with prompt .
4. When prompt appears, type the subsequent command: sfc /scannow /offbootdir=d:\ /offwindir=d:\windows.
5. Press Enter and restart your computer after the method.